Thanks For Using The Performance of a Lifetime!



Chatroom Auctions & Paid Classifides DDDPL's Additional Job Search










FAQ
Last visit was: Mon Sep 25, 2017 8:13 pm
It is currently Mon Sep 25, 2017 8:13 pm



 [ 1 post ] 
 "Learn how to Build Your Own Wakeboard Slider and..." 
Author Message
User avatar

Joined: Mon Sep 13, 2010 1:47 pm
Posts: 45372
Post "Learn how to Build Your Own Wakeboard Slider and..."
Learn how to Build Your Own Wakeboard Slider and Wakeboard Slider Tips
by: David Hagerman




How can you build your own wakeboard slider?

Every single wakeboard lover devotes considerable amount of time wondering how he can possess a wakeboard slider. This had been a serious hurdle on the way of wakeboard lovers to venture out on a wakeboarding spree.

However, this hurdle is in its course of ebb as there are some tips before the wakeboard lovers to construct a wakeboard slider for themselves. There are certain easy instructions to be followed and eventually you can turn out to be an expert in building wakeboard sliders.

To set on with the learning process you must decide on the size of the slider you desire to build. In this regard if you are just a beginner and is unaware of the most suitable size for yourself, then it would be wise to start with a comparatively smaller size of four feet. To set off for acquiring the skill of making a wakeboard slider one must possess the certain materials required for making the wakeboard slider. These resources include plastic drums, plywood, PVC cleaner, PVC internal unions, cement, screws and toggle bolts.

Firstly, you must make a basic frame having a length of 12 feet and a breadth of 6 feet for supporting and holding the drums. Secondly, the drums need to be enclosed from all the four corners enabling the barrel not to fit all through the way with the usage of the quest for strength. After this, supports should be made for the long beam which is four feet. In the next place, angle braces should be attached to each for checking the dangerous right and left movements and to support the plywood, which you will be attaching later. In the next place, you need to attach more support inside the main slider to embark a preventive check on the back and forth movements. This entire set up is now ready to be assorted with the other set up.

The previously built up set up is to be mounted on the PVC and the two ends are to be joined. Scabs of softwood can also be used for joining the two ends. Followed by this, the PVC is to be attached by using the standard toggles bolts. Usually people prefer using them at a distance of nearly 4 feet because it paves the way for the nuts to face the direction in which the tube would be running. After this is done, the rear slider can be added. This slider needs to be hung from the backend of the framework.

Now the front portion of the slider should evenly be placed at the rear but while doing so be cautious about the fact that gaps are not be left. In this case, the internal PVC can also be used. The arc is now to be added to the front portion allowing the tubes to go underwater. The slider seems to be almost completed. The braces are to be applied throughout the arc. Thus the slider is ready to be painted colorfully as the owner would like it.

Wakeboard lovers can easily undergo the botherations of erecting a wakeboard slider for themselves, which can in turn serve as a faithful companion on a wakeboarding spree.


About The Author
Go to Wakeboard Zone today to get your free ebook on Wakeboarding today at http://www.wakeboardzone.org/. Wakeboard Zone has tons of information on Wakeboarding and lots of forums where you can connect with others who love to Wakeboard and you can find Wakeboard Zone at http://www.wakeboardzone.org/. Get your Free Ebook today at http://www.wakeboardzone.org/.

Visit the author's web site at:
http://www.wakeboardzone.org/




Copyright © 2001-Present ArticleCity.com
[Note: Due to a size limitation, the title, above, had to be abbreviated. Apologies to the author and ArticleCity.com. - Admin]
This article was posted by permission.


Wed Feb 23, 2011 10:52 am
 [ 1 post ] 

Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  






Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by ST Software for PTF.